background image

53

MAINTENANCE

ENGLISH

Note that while the testing was performed under 
standard laboratory conditions, actual performance 
may vary. 

Service Flow

0.5 gpm (1.9 lpm)

Water Supply

Community or private well 

— Potable Water

Water Pressure

20 -120 psi (138 - 827 kPa)

Water Temperature

33-100°F (0.6 -37.8°C)

Capacity

200 gallons (757 liters)

NSF System Trade Name Code : ADQ73613401-S 
NSF Replacement Code : ADQ73613401

Read, understand, and follow all safety Information contained in these instructions prior to installation and 
use of this product. Retain these instructions for future reference.

 WARNING

To reduce the risk associated with the ingestion of contaminants:

 

Do not

 use with water that is microbiologically unsafe or of unknown quality without adequate 

disinfection before or after the system. Systems certified for cyst reduction may be used on 

disinfected water that may contain filterable cysts.

  CAUTION

Please note that water could leak while replacing the filter which could result in property damage.
To reduce the risk associated with property damage due to water leakage:

 

Read and follow

 Use Instructions before installation and use of this system.

 

Installation 

must

 comply with existing state or local plumbing codes.

 

Protect filter from freezing

 Drain filter when room temperature drops below 33°F (0.6°C). 

 

Do not

 install if water pressure exceeds 120 psi (827 kPa). If your water pressure exceeds 80 psi, 

you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how 

to check your water pressure.

 

Do not

 install where water hammer conditions may occur. If water hammer conditions exist you 

must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to 

check for this condition.

 

Do not

 install on hot water supply lines. Install on cold water lines only. The maximum operating 

water temperature of this filter system is 100°F (37.8°C).

 

Where a backflow prevention device is installed on a water system, a device for controlling pressure 

due to thermal expansion must be installed.

 

The disposable filter cartridge 

must

 be replaced every six months, at the rated capacity or if a 

noticeable reduction in flow rate occurs.

NSF is a trademark of NSF International. LG is a trademark of LG Corp. MCM Co..Ltd.

Application Guidelines / Water Supply Parameters

SAFETY INFORMATION

It is essential that the manufacturer’s 
recommended installation, maintenance and filter 
replacement requirements be carried out for the 
product to perform as advertised.

Replacement Cartridge: ADQ73613401

For estimated costs of replacement elements 
please call 1-877-714-7486 or visit our website at 
www.LGSIGNATURE.com

Refer to the “warranty” section of the 
Refrigerator Owner’s Manual for Limited Warranty 
information.

Summary of Contents for URNTC2306N











































































Reviews: