Diagnostic Information 2-22
4049-XXX
If the displayed error is 977, verify that the network card is installed
and grounded correctly. Remove the network card and check for +5
VDC at pin B24 of RIP board J6 or J12 (whichever the network card
was connected to). If the voltage is incorrect replace the engine
board; if there is +5 VDC replace the network card.
Network Wrap Tests
Token-Ring with Shielded Twisted-Pair Cable: Disconnect the
LAN cable from the electrical outlet, leaving it connected to the
printer network card.
Ethernet 10BASE2: Attach a 50 Ohm BNC terminator cap to each
end of the T-connector. The customer may be able to provide this
cap.
There is no wrap test for Token-Ring with Unshielded Twisted-Pair
cable or for Ethernet 10Base -T.
POR the printer. If the printer completes POR successfully, the
printer, network card, and the port to the LAN are working correctly.
If the customer still has a problem printing,
see
Output Bin Sensor
Examine the bin area for obstructions or damage. Run the diagnos-
tic sensor test.
Make sure the plastic bails and guide are in good condition and that
they guide the sensor flag out of and into the sensor as paper
passes into the bin. On the sensor, the voltage from pin 2 to pin 3
(pin 1 is the bottom pin) should change from 0 to +5 VDC as the sen-
sor is blocked and unblocked. Pin 1 should always m5 VDC.
Replace the sensor, the sensor card or the operator panel/bin sen-
sor cable as necessary.
Operator Panel Problem
Note: If the printer is in “Menus Disabled” mode, you can activate
the menus by powering on the printer with the Return button and the
top button pressed. Repeat the POR procedure to disable the
menus again after service.
Summary of Contents for Optra 4049 Series
