Lexmark ExecJet II 4076 User Manual Download Page 54

Page: 54 / 89

4076-0XX

Paper Release Lever Removal

1. Remove the top cover.

2. Pull the paper release lever forward.

3. Place a screw driver into the slot [A] of the paper release lever.

Push the screw driver down to release the latch, then remove
the lever.

Power Supply Removal

1. Remove the top cover.

2. Disconnect the print head cables from the system board. You

may have to open the print head cable connectors on the system
board first, then disconnect the cables.

3. Disconnect connectors J4, J5, and J6 from the system board.

4. Remove the machine from the base. To do this, push the frame

latches out as you lift the machine from the base. Set the
machine aside.

5. Disconnect the power supply cable from the system board.

6. Remove the 4 power supply mounting screws and remove the

power supply.

NOTE: The fuse on the power supply is for safety pur- poses only. If
it blows, there is a bad component on the board. Do not replace the
fuse. A new fuse will not correct the failure.

Summary of Contents for ExecJet II 4076


























































































Search results

Summary of Contents for ExecJet II 4076

Reviews:

Related manuals for ExecJet II 4076

Brands by name

Popular brands

Lexmark ExecJet II 4076, User Manual

Search results

Summary of Contents for ExecJet II 4076

Reviews:

Related manuals for ExecJet II 4076

Brands by name

Popular brands