Lexmark C792de Service Manual Download Page 596

Page: 596 / 630

7-36

Service Manual

5062

40X7168

(Cont.)

10J0937

Thermistor &
redrive cable

Behind fuser

System board connector:
JFSRD1

See

“Fuser thermistor removal”

on page 4-66

10J0939

HVPS cable

Under HVPS board

• System board connector:

JHVPS1

See

“High-voltage power supply

(HVPS) board removal” on
page 4-67

10J0942

Input option
cable

Bottom frame

• System board connector:

JIOPT1

1. Remove the bottom plate of the

printer. See steps

through

“MPF breakaway assemblies
removal” on page 4-94

2. Push the cable up through the

frame.

3. Stand the printer back up, and

remove the cable

Note: Use cable ties to attach the
toroid to the new cable.

10J0947

Ground strap
cable

Front system board cage
support above LVPS

1. Remove the rear cover. See

“Rear cover removal” on
page 4-18

2. Remove the strap from the top of

the LVPS.

10J0948

Duplex door
beacon cable,
side

Behind LVPS exit duct, through
left rear frame to left access
door

• System board connector:

JDDLED1

See

“LVPS exit duct removal” on

page 4-85

and

“Left cover removal” on
page 4-10

10J0949

Ref edge
ground cable

Staging paper path reference
edge

See

“Staging paper path

reference edge assembly
removal” on page 4-136

10J0951

Paper path
redrive sensor
cable

Paper path redrive

• System board connector:

JRDR1

See

“Paper path redrive assembly

with sensors removal” on
page 4-113

10J0953

Blower & right
side waste
cable

Behind blower, on top frame
under printhead access cover

• System board connector:

JBLW1

See

“Printhead access cover

removal” on page 4-17

10J0957

Duplex unit
cable

Behind LVPS exit duct, through
left rear frame to left access
door

• System board connector:

JDP1

See

“LVPS exit duct removal” on

page 4-85

and

“Left cover removal” on
page 4-10

10J0967

Waste toner
full cable

• System board connector:

JWTBF1

See

“Waste toner full cable

removal” on page 4-150

40X7169

10J0963

Front host
USB cable

Operator panel assembly,
connected to UICC card

See

“Host USB cable removal” on

page 4-71

10J0970

Card reader
cable

Operator panel assembly,
connected to UICC card

See

“OP panel cover removal” on

page 4-17

10J0971

Operator
panel USB
cable

Under top cover

• System board connector:

JFMUSB

See

“Top cover removal” on

page 4-28

10J0972

UICC cable

Operator panel assembly

• System board connector:

See

“OP panel display removal”

on page 4-109

Cable location table

P/N

item number

Description

Location

To access

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for C792de

Reviews:

Related manuals for C792de

Brands by name

Popular brands

Lexmark C792de, Service Manual

Search results

Summary of Contents for C792de

Reviews:

Related manuals for C792de

Brands by name

Popular brands