manualshive.com logo in svg

Lexmark C792de, Service Manual

The Lexmark C792de is a high-quality color laser printer perfect for any office setting. For troubleshooting and maintenance, download the free Service Manual from our website. This comprehensive manual will guide you through any technical issues, ensuring your printer stays running smoothly. Download it now from manualshive.com.

Share
Download
background image

4-66

Service Manual

5062

11.

Push in the tab (E) to disconnect the cable from the LVPS, and remove the cable.

Fuser thermistor removal

See 

“Fuser thermal guide assembly” on page 7-37

 for the part number.

1.

Remove the fuser. See 

“Fuser assembly removal” on page 4-58

.

2.

Disconnect the cable (A).

3.

Remove four screws (B) to remove the thermistor.

E

A

B (88A0212)

Summary of Contents for C792de























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C792de

Samsung CLX-9350ND Service Manual preview
CLX-9350ND
Brand: Samsung Pages: 549
Canon PIXMA MG3120 Getting Started Manual preview
PIXMA MG3120
Brand: Canon Pages: 4
Xerox Phaser 6300 Service Manual preview
Phaser 6300
Brand: Xerox Pages: 13
Lexmark X642 Clearing Jams Manual preview
X642
Brand: Lexmark Pages: 4
Genicom Intelliprint cL160 User Manual preview
Intelliprint cL160
Brand: Genicom Pages: 216
Oce VarioPrint 4110 User Manual preview
VarioPrint 4110
Brand: Oce Pages: 216
Oki ES9455 Printing Manual preview
ES9455
Brand: Oki Pages: 204
Ricoh IM C530 Series User Manual preview
IM C530 Series
Brand: Ricoh Pages: 288
NEC 4650NX - SuperScript Color Laser Printer Network Manual preview
4650NX - SuperScript Color Laser Printer
Brand: NEC Pages: 74
Oki C6150dn Manual De L'Utilisateur preview
C6150dn
Brand: Oki Pages: 309
Lexmark 13C1101 Brochure & Specs preview
13C1101
Brand: Lexmark Pages: 8
Domino Macrojet 2 Product Manual preview
Macrojet 2
Brand: Domino Pages: 114
DataCard C3000 Brochure preview
C3000
Brand: DataCard Pages: 4
Canon imagePROGRAF iPF670E Setup Manual preview
imagePROGRAF iPF670E
Brand: Canon Pages: 6
Canon imagePROGRAF iPF 655 Specifications preview
imagePROGRAF iPF 655
Brand: Canon Pages: 2
Canon imagePROGRAF PRO 1000 Installing Instructions preview
imagePROGRAF PRO 1000
Brand: Canon Pages: 17
Canon imagePROGRAF iPF8400S Service Manual preview
imagePROGRAF iPF8400S
Brand: Canon Pages: 38
Canon imagePROGRAF SD-22 Setup Manual preview
imagePROGRAF SD-22
Brand: Canon Pages: 14

Brands by name

Popular brands

Load more brands