Lexmark 4500-00 Series Service Manual Download

Page: 73 / 246

Diagnostic information

2-43

4500–E220/E321/E323

Service error secondary light patterns

Quickly press and release

Continue

twice to obtain the secondary

light pattern.

Note:

There are many tertiary codes following these secondary
codes. The following pages show these codes.

Ready/

Dat

Toner

Low

Load/

Rem

ove Paper

Paper

ess Co

inue

Service Condition

✳

❍

Software error (90x)

✳

❍

✳

Transfer roll error (91x)

✳

❍

✳

❍

Fuser / toner sensor error (92x)

✳

❍

✳

Printhead / transport motor /
RIP to engine error (93x)

✳

❍

✳

❍

RIP to engine / engine
communication error (94x)

✳

❍

✳

❍

✳

NVRAM / ROM / not AND
(NAND) error (95x)

✳

❍

✳

❍

RAM memory error (96x)

✳

❍

✳

Network error (97x)

✳

❍

✳

❍

Paper port communication
error (98x)

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands