manualshive.com logo in svg

Lexicomm ViLX-228, Installation And Commissioning Manual

Share
Download
Lexicomm ViLX-228 Installation And Commissioning Manual Download Page 14

 

 

 

Document PViLX228 7001-06 Rev 6 2017 

Page 14 of 24 

 

Exchange PCB Diagram- 

 

6.2

 

Adding a Line Card 

The ViLX-228 Master Station is supplied with at least one number Line Card.  There are 2 lines per 

Line Card.   

Before adding a Line Card, ensure that the ViLX-228 Master Station is not powered. If the ViLX-228 

Master Station is powered, then power down the ViLX-228 Master Station (see 5.10).  

To fit the Line Card: 

1.

 

Place Line Card in the next available space on the Exchange PCB and secure using the supplied 

screw.   

2.

 

Remove the line terminal and connect the field wiring.  

3.

 

Push the terminal into the correct position on the Line Card.  

4.

 

Set the dipswitch on the Display PCB (see 6.1) to enable Line Card monitoring.   

Once the Line Card is securely fitted, power up the ViLX-228 Master Station (see 5.9).  

6.3

 

Removing a Line card 

Before removing a Line Card, ensure that the ViLX-228 Master Station is not powered. If the ViLX-228 

Master Station is powered, then power down the ViLX-228 Master Station (see 5.10).  

 

To remove the Line Card: 

1.

 

Remove all line terminals from the Line Card that is to be removed. 

2.

 

Remove the securing screw. 

3.

 

Remove the Line Card from Exchange PCB. 

4.

 

Set the dipswitch on the Display PCB (see 6.1) to disable Line Card monitoring. 

Once the Line Card has been removed, the ViLX-228 Master Station may be powered (see 5.9). 

6.4

 

Adding a ViLX-228 Repeater Station 

The ViLX-228 Master Station has in-built networking which means a single additional ViLX-228 Master 

Station can be added. This additional ViLX-228 Master Station is designated as the ViLX-228 Repeater 

Station.  The ViLX-228 Repeater Station must be wired as a ring to comply with BS5839pt9:2011 

The 4 Line Cards can be distributed between the ViLX-228 Master Station and the ViLX-228 Repeater 

Station in any combination, as long as the Line Cards do not occupy the same position on the Exchange 

PCB in both the ViLX-228 Master Station and the ViLX-228 Repeater Station, i.e. if a Line Card is in 

position 1 (Lines 1&2) on the ViLX-228 Master Station, then no Line Card can be placed into position 1 

(Lines 1&2) on the ViLX-228 Repeater Station. 

Network connections used are Network Out and Network In, with Network In on one Station wired to 

Network Out on the other Station (A to A, B to B, C to C, and D to D).  

The default network address setting for the ViLX-228 Master Station is 1. When adding a ViLX-228 

Repeater Station, it must share the same address as the ViLX-228 Master Station. 

Summary of Contents for ViLX-228

























Reviews:

No comments

Brands by name

Popular brands

Load more brands