LEVTECH LSP-TST User Manual Download Page 6

6

 

2.2.  Receipt and unpacking 

 

2.3.  Environment 

 

2.4.  Mounting 

 

 

 

 

  

2.

 

 

 

 

2.1.

 

Symbols

 

 

 

 

 

 

 

 

 

 

WARNING

CAUTION

NOTICE

 

 

 

This symbol indicates information that, if ignored, could result possibly in 
personal injury or even death due to incorrect 

h

andling.

This symbol indicates information that, if ignored, could possibly result in 
personal injury or physical damage due to incorrect handling.

Indicates information considered important, but not hazard-related.

Unpack the device without damaging it and check whether the device type corresponds 
to the one ordered. The packing should always follow the device until this has been 
permanently mounted.

Avoid direct sunlight, dust, high temperatures, mechanical vibrations and shock, and rain 
and heavy moisture.

Only technicians who are familiar with the technical terms, warnings, and 
instructions in the manual and who are able to follow these should connect the 
device.

Mounting and connection of the device should comply with national legislation for 
mounting of electric materials, i.e. wire cross section, protective fuse, and location.
Descriptions of input / output and supply connections are shown in this installation 
guide and on the side label.

Use this device only in accordance with this instruction manual, as well as all 
applicable local and national laws and regulations. Only allow this device to be 
installed, operated, maintained, repaired, etc. by others who have also read and 
understood the user manual. 

Do not allow minors, untrained personnel, or personnel suffering from physical or 
mental impairment that would affect their ability to follow this manual to install, 
operate, maintain, or repair this device.

Any untrained personnel who might be near the device while it is in operation 
MUST be informed that it is dangerous and fully instructed on how to avoid injury 
during its use.

SAFETY

 

INSTRUCTIONS

Summary of Contents for LSP-TST

















Reviews: