LEVITON UPB™ 6-BUTTON SCENE SWITCH WITH IR RECEIVER
Cat. No. 38A00-1
Installation Instructions and User’s Guide
INSTALLATION
ENGLISH
DI-022-HL381-05A
AR2243
(38I00-1)
Leviton UPB™ 6-BUTTON SCENE SWITCH OPERATION
The Leviton UPB™ 6-Button Scene Switch has many configurable items that can be set using the UPB™ UPStart configuration software.
The following describes the operation of the Leviton UPB™ 6-Button Scene Switch in its factory default configuration.
The Leviton UPB™ 6-Button Scene Switch has six pushbuttons labeled ON, A, B, C, D, and OFF (although these buttons may be custom engraved), which are used to control six
lighting scenes. When the pushbutton labeled "ON" is pressed, the LED behind the "ON" pushbutton is illuminated and any other is turned off. When the pushbutton labeled "OFF"
is pressed, the LED behind the "OFF" pushbutton is illuminated and any other is turned off. When one of the pushbuttons labeled "A", "B", "C", or "D" is pressed, the LED behind the
respective pushbutton is illuminated and any other is turned off. No more than one pushbutton is illuminated at a time.
WARNINGS AND CAUTIONS
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and
test that power is off before wiring!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
WARNINGS AND CAUTIONS
• Use this device with
copper or copper-clad wire only.
• For indoor use only.
• SAVE THESE INSTRUCTIONS.
Figure 1 - Leviton UPB™
6-Button Scene Switch
Leviton UPB™ 6-Button Scene Switch Overview
The Leviton UPB™ 6-Button Scene Switch
(Figure 1) allows for lighting control of a room where Leviton UPB™ Wall Switches have been
installed. It uses the UPB™ two-way powerline communication technology to communicate with Leviton controllers, UPB™ Wall Switches,
and other UPB™ devices on the network.
The Leviton UPB™ 6-Button Scene Switch has six pushbuttons labeled ON, A, B, C, D, and OFF (although these buttons may be custom
engraved). Each pushbutton is slightly backlit so that the buttons can be seen in a dark room. Depending on configuration of the Leviton
UPB™ 6-Button Scene Switch, one or more of the six pushbuttons will be distinctly illuminated, indicating the pushbutton has been pressed
or a scene has been selected. Each lighting scene pushbutton (A-D) can be configured to custom fit an individual’s lifestyle and desires.
UPB™ Wall Switch Dimmers are capable of storing preset light levels and fade rates to create powerful lighting scenes.
The Leviton UPB™ 6-Button Scene Switch is also equipped with an IR receiver. Using the Leviton 38A14-1 Scene Switch Remote Control,
or any learning remote control, the pushbuttons on the Scene Switch can be activated. Point the remote control at the Scene Switch and the
room can be turned on, turned off, dimmed, brightened, or set to a scene (A-D).
ON
A
B
C
D
OFF
Figure 2 – Changing
Switch Color
Changing Switch Color
The color of the Leviton UPB™ 6-Button Scene Switch may be changed to complement the interior décor. The Leviton
UPB™ 6-Button Scene Switch is supplied with a white bezel. Additional colors are available; contact your Leviton distributor
for more information. When changing the bezel, make sure that the Leviton UPB™ 6-Button Scene Switch is disconnected
from all power, and proceed as follows:
1. The bezel attaches to the Leviton UPB™ 6-Button Scene Switch with two small Philips head screws: one on the upper-
right corner and one on the lower-left corner
(Figure 2).
2. Using a small-bladed Philips screwdriver, unscrew each of the two screws. Remove the bezel from the back housing.
3. Install the new bezel by aligning the mounting holes on the bezel with the installation pins on the back housing. Secure
bezel to back housing with the two Phillips screws that were removed in
Step 1.
Figure 3 – Wiring Diagram
INSTALLATION INSTRUCTIONS
1. TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
2. If applicable, remove the faceplate from the existing device, remove the existing device from the wall box, and disconnect the wires
from the existing device. Identify the "Line" (black) and "Neutral" (white) wires.
3.
Remove 3/4" of insulation from each of the wires on the Leviton UPB™ 6-Button Scene Switch. Install the Leviton UPB™ 6-Button
Scene Switch by connecting wires per wiring configuration shown in
Figure 3.
4. After all connections have been made, be certain that all wire connectors are firmly attached and there is no exposed copper.
5. Gently place the wires and Leviton UPB™ 6-Button Scene Switch into the wall box with the ON pushbutton at the top of device.
Using the supplied screws, attach the Leviton UPB™ 6-Button Scene Switch to the wall box.
6. Before installing the faceplate, restore power to the circuit for testing.
7. After testing the Leviton UPB™ 6-Button Scene Switch for proper local operation, install a Decora
®
faceplate over the Leviton UPB™
6-Button Scene Switch.
MAIN
CIRCUIT
BREAKER
PANEL
120VAC
60Hz
38A00-1
6-BUTTON
SCENE
SWITCH
BLACK
LINE
NEUTRAL
WHITE
Pushbutton Operation
In its factory default configuration, the "ON" pushbutton will brighten the UPB™ Wall Switch Dimmers to 100% at each switch’s default fade rate when pressed. When the "ON"
pushbutton is double-tapped, the UPB™ Wall Switch Dimmers will snap to 100%. When pressed or double-tapped, the “ON” pushbutton will illuminate and any others are turned off.
The "ON" pushbutton is also used to brighten the last lighting scene that was turned on. When the "ON" pushbutton is pressed and held down, the UPB™ Wall Switch Dimmers will
slowly brighten, and then stop brightening when the "ON" pushbutton is released.
In its factory default configuration, the "OFF" pushbutton will fade the UPB™ Wall Switch Dimmers to 0% (off) at each switch’s default fade rate when pressed. When the "OFF"
pushbutton is double-tapped, the UPB™ Wall Switch Dimmers will snap to 0%. When pressed or double-tapped, the "OFF" pushbutton will illuminate and any others are turned off.
The "OFF" pushbutton is also used to dim the last lighting scene that was turned on. When the “OFF” pushbutton is pressed and held down, the UPB™ Wall Switch Dimmers will
slowly dim, and then stop dimming when the “OFF” button is released.
In its factory default configuration, the "A" pushbutton will brighten the UPB™ Wall Switch Dimmers to 80% at each switch’s default fade rate when pressed or double-tapped.
When pressed, the "A" pushbutton will illuminate and any others are turned off.
In its factory default configuration, the "B" pushbutton will brighten the UPB™ Wall Switch Dimmers to 60% at each switch’s default fade rate when pressed or double-tapped.
When pressed, the "B" pushbutton will illuminate and any others are turned off.
In its factory default configuration, the "C" pushbutton will brighten the UPB™ Wall Switch Dimmers to 40% at each switch’s default fade rate when pressed or double-tapped.
When pressed, the "C" pushbutton will illuminate and any others are turned off.
In its factory default configuration, the “D” pushbutton will brighten the UPB™ Wall Switch Dimmers to 20% at each switch’s default fade rate when pressed or double-tapped.
When pressed, the "D" pushbutton will illuminate and any others are turned off.
CONFIGURING THE Leviton UPB™ 6-BUTTON SCENE SWITCH
The Leviton UPB™ 6-Button Scene Switch is designed to control a room of lighting using Leviton Lighting Control (HLC) but also has several configuration options that can be
enabled or modified using the UPB™ UPStart configuration software.
WEB
VERSION
