COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your Leviton distributor and proceed as follows (please note that
wallplate must be removed).
1.
Select the color of the face you desire.
2.
The frame has snaps on its sides. Using a small screwdriver,
gently
remove the frame from the strap
(refer to Figure 2)
.
3.
Take the new frame and position it properly to the strap. Notice that the frame has a cut-out for the air-gap switch
lever. Line up the plastic snaps with the square holes in the strap. Insert the snaps on one side of the frame into the
strap.
4.
Firmly press sideways and down to slip the other snaps into place. The frame snaps in with a audible click.
Ensure that all four snaps are secure. Replace Decora
®
wallplate.
The color conversion is complete.
TO PROGRAM
Programming scenes occurs at the Scene Controller for this dimmer. If programming is required, refer to Scene
Controller’s instruction sheet.
TO OPERATE
ON:
Tap the upper half of the rocker. The lights will brighten to the last set light level.
OFF:
Tap the lower half of the rocker. The lights will dim to OFF.
BRIGHTEN:
Press and hold the upper half of the rocker to the desired light level.
FULL BRIGHT:
If the lights are OFF, double tap the upper half of the rocker. The lights will turn ON FULL BRIGHT.
If the lights are ON, tap the upper half of the rocker once. The lights will turn ON FULL BRIGHT.
The previous light level will remain in memory upon next ON operation
(see above)
.
FAST OFF:
Double tap the bottom half of the rocker. The lights will immediately turn OFF.
DIM:
Press and hold the lower half of the rocker to the desired level.
BRIGHTNESS LEVEL DISPLAY:
Indicates the level of brightness when the lights are ON. Indicates the previous level of brightness when the lights are
OFF
(refer to Figure 1)
.
NOTE:
To alert you that there is power to the dimmer when the load is OFF, the ON/OFF LED remains ON. To
alert you that the load is ON, the ON/OFF LED remains OFF.
NOTE:
If lights are OFF, regardless if you tap or press and hold the upper half of the rocker, the lights will go to
last set light level.
NOTE:
If a power interruption should occur while the device is ON, the light load will return to its previous light level
when power is restored within 10 seconds.
TROUBLESHOOTING
•
Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp switch is OFF, if applicable.
- Ballast has failed.
- Ballast is not connected to line Neutral.
- Air gap switch is open.
•
Dimmer does not operate
- Dimmer BLACK wire miswired to ballast and Dimmer BLUE wire miswired to LINE Hot.
•
Light turns ON and Dimmer works, but Controller does not work
- There are no connections from Controller to Dimmer (YELLOW wire).
- Controller is miswired.
•
Lights Flickering
- Lamp has a bad connection.
- Lamp power is less than 60VA.
Hot (Black)
Neutral (White)
Scene Capable
Dimmer
Blue
White
Black
Yellow
Yellow
White
Black
Line
120VAC, 60Hz
Scene Controller
Green
Ground
Black
White
Ballast
Red
Blue
Yellow
To Lamps
Primary
Side
Hot (Black)
Neutral (White)
Load
Scene Capable Dimmer
(Incandescent)
Scene Capable Dimmer
(Mark X)
Blue
Blue
White
White
Black
Black
Black
Yellow
Yellow
Yellow
Black
White
Black
White
Line
120VAC, 60Hz
Scene
Controller
Scene
Controller
Green
Ground
Green
Ground
Black
White
To Lamps
Primary
Side
Ballast
Red
Blue
Yellow
Wiring Diagram 1 – Two Location Control Application
Wiring Diagram 2 – Scene Dimming: Fluorescent and Line Voltage with
Multiple Scene Controllers and Scene Dimmers
Wiring Diagram 3 – Scene Dimming: Fluorescent and Line Voltage with
Multiple Scene Controllers and Dimmer on Two Circuits
Scene
Dimmer
(Mark X)
Scene
Dimmer
(Incandescent)
Scene
Controller
17100-2WY
REPEATER
2-Way
Scene
Controller
Black
120VAC, 60Hz
Black
Red
Neutral B
Neutral A
Yellow
Yellow
Black
Yellow
Blue
White
White
Gray
Yellow/Red
Line B
Line A
Load
White
White
Yellow
Black
Black Yellow
Circuit A Circuit B
Green
Ground
Green
Ground
Black
White
To Lamps
Primary
Side
Ballast
Red
Blue
Yellow
Blue
DI-00X-MCX10-00A
Frame
Strap
Air-Gap
Switch
Snaps
Push in 2 Locations
ON/OFF
LED
Brightness Level Display
Figure 2 - Color Conversion
DI-00X-MCX10-00A
10/4/02, 10:28 AM
2
