manualshive.com logo in svg

LevelOne FCS-3056, Hardware User Manual

Share
Download
LevelOne FCS-3056 Hardware User Manual Download Page 2

  Hardware Manual 

                 

2 

Table of Contents 

 

Precautions ............................................................. 4

 

Safety Instructions .................................................................................... 6

 

Introduction ............................................................. 7

 

The List of Models ..................................................................................... 7

 

Package Contents ...................................................................................... 7

 

Physical Description ................................................................................. 8

 

Before Installation................................................. 10

 

How to Connect DI/Do Devices ............................................................... 10

 

How to Connect Audio Devices .............................................................. 13

 

Installing the Camera on a Surface ..................... 14

 

Step 1: Drill the Holes .............................................................................. 14

 

Step 2: Open the Dome Cover ................................................................ 15

 

Step 3: Install the Camera to the Surface .............................................. 16

 

Step 4: Connect the Cable ...................................................................... 17

 

Step 5: Access the Camera Live View .................................................... 18

 

Step 6: Adjust the Viewing Angle and Focus ........................................ 18

 

Step 7: Close the Dome Cover ................................................................ 18

 

Other Adjustments and Accessories .................. 20

 

How to Adjust the Camera Viewing Angle and Focus .......................... 20

 

FCS-3064 Camera Models ................................................................... 20 

Summary of Contents for FCS-3056

































Reviews:

No comments

Brands by name

Popular brands

Load more brands