Let's Go Aero GearSpace HGK819 Product Manual Download Page 6

Page 6 of 6

If a Let’s Go Aero bike rack is found to have a defect in workmanship or material over the lifetime of the original purchaser, Let’s Go 

Aero will repair or replace the defect free of charge. This warranty terminates if a purchaser transfers the product to any other person.  

The warranty does not cover damage or wear which occurs as a result of day to day use or general wear and tear. No warranty is given 

for defects caused by normal wear and tear, cosmetic rust, scratches, accidents, unlawful vehicle operation, or modification of, or any 

types of repair of, a load carrier system other than those authorized by Let’s Go Aero.

No warranty is given for defects resulting from conditions beyond Let’s Go Aero’s control including, but not limited to, misuse, overload-

ing, or failure to assemble, mount or use the product in accordance with Let’s Go Aero’s written instructions or guidelines included with 

the product or made available to the purchaser.

Subject to the limitations and exclusions described in this warranty, Let’s Go Aero will remedy defects in materials or workmanship by 

repairing or replacing any parts diagnosed to be at issue without charge for parts or labor. In the event that a product is defective, the 

purchaser should contact the Let’s Go Aero dealer from whom the product was purchased. If the dealer is not able to correct the defect, 

the purchaser should contact Let’s Go Aero in writing to [email protected] or by phone at 877-464-237 or 719-630-3800. 

In the event that a product needs to be returned to Let’s Go Aero, a Let’s Go Aero technician will provide the purchaser with the ap-

propriate mailing address and any additional instructions. Proof of purchase in the form of an original purchase invoice or receipt, and a 

detailed description of the defect must be provided. Please note that a Return Merchandise Authorization (RMA) from Let’s Go Aero is 

required for any returns. 

DISCLAIMER OF LIABILITY REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR THE ISSUANCE OF A REFUND OR 

CREDIT (AS DETERMINED BY LET’S GO AERO) IS A PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY. DAMAGE 

TO A PURCHASER’S VEHICLE, CARGO AND/OR TO ANY OTHER PERSON OR PROPERTY IS EXCLUDED.

THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING 

THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

LET’S GO AERO’S SOLE LIABILITY TO ANY PURCHASER IS LIMITED TO THE REMEDY SET FORTH ABOVE. IN NO EVENT WILL 

LET’S GO AERO BE LIABLE FOR ANY LOST PROFITS, LOST SALES, OR FOR ANY CONSEQUENTIAL, DIRECT, INDIRECT, INCI-

DENTAL, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES OR FOR ANY OTHER DAMAGES OF ANY KIND OR NATURE.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE 

ABOVE LIMITATIONS MAY NOT BE APPLICABLE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO 

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Limited Lifetime Warranty

Summary of Contents for GearSpace HGK819







Reviews: