Let's Go Aero BikeTree B01618 Manual Download Page 3

PAGE 3 OF 5

STEP 3

Install Wing [

G

] onto V-Base [

A

using Wire Lock Pin [

E

]. 

Open wire lock pin [

E

] as shown in 

DETAIL 7. Insert wire lock pin [

E

through the interior hole at the end 

of the Wing [

G

] and out the exterior 

side of the carrier. (You may need 

to slide Wing [

G

] up slightly to align 

the holes). Close Wire Lock Pin [

E

by positioning the loop end of the 

wire over the pin and allowing it to 

spring back against the Wing [

G

as shown in DETAIL 7.
Install the remaining Wing [

G

using the remaining Wire Lock Pin 

[

E

].

D

BIKETREE GUIDELINES

The BikeTree bicycle system’s maximum load weight is 80 lbs. Do not exceed this carrying capacity. Do not exceed the 

receiver hitch manufacturer’s tongue weight rating.
Do not use this rack and accessories for purposes other than those for which they were designed. Failure to follow the 

guidelines of the product’s instructions will void the warranty.
Keep bicycle tires away from vehicle’s hot exhaust flow by at least 6 inches.

ONE YEAR LIMITED WARRANTY

Let’s Go Aero warrants this product to be free from defect in material and workmanship for one year (retain your sales re-

ceipt for your records). Any product or part thereof found to be defective within that period will be replaced without charge 

provided that: (1) the product was not misused; (2) no alterations or modifications were made; (3) its failure was not a 

result of normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Let’s Go 

Aero.  Manufacturers only obligation shall be to replace such products or parts proved to be defective. A Return Merchan-

dise Authorization is required prior to return. Please contact Let’s Go Aero toll-free, at 877-464-2376 or 719-630-3800, or 

via email to [email protected] to get an RMA number. This warranty terminates if a purchaser transfers the product 

to any other person. No warranty is given for LGA products purchased outside of the United States and Canada.

To register your product, visit the Let’s Go Aero website at www.LetsGoAero.com

For assistance with this bicycle carrier, please contact Let’s Go Aero:

4474 Barnes Rd, Colorado Springs, CO 80917
Phone:  877-464-2376 or 719-630-3800

Email: [email protected]
To learn more about our line of bicycle carriers for vehicle, home storage, and accessory options for carrying fat bikes, 

snowboards/skis, and more, be sure to visit our website: www.LetsGoAero.com
U.S. Patent No: D717716; D717717; D684917; 8,889,456; D722289; Patents Pending

For More Information & Accessories,

Visit our Website - www.LetsGoAero.com

Contact Us at 877-474-2376 or 719-630-3800 | Email [email protected]

Copyright © 2017 Lets Go Aero Inc.

A

G

E

E

E

DETAIL 5

DETAIL 6

DETAIL 7

Summary of Contents for BikeTree B01618






Reviews: