Leonton EG5-1802-SFP Series User Manual Download Page 3

FCC Notice

 

This  equipment  has  been  tested  and found to  comply  with  the  limits  for  a  Class-A  digital device, 
pursuant  to  Part  15  of  the  FCC  rules.  These  limits  are  designed  to  provide  reasonable  protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy. It may cause harmful interference to radio communications if the 
equipment  is  not  installed  and  used  in  accordance  with  the  instructions.  However,  there  is  no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

 

 

Reorient or relocate the receiving antenna.

 

 

Increase the separation between the equipment and receiver.

 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected.

 

 

Consult the dealer or an experienced radio/TV technician for help.

 

 
 

Caution: Any changes or modifications not expressly approved by the grantee of this device could 
void the user's authority to operate the equipment.

 

 
 

Déclaration FCC 

Cet équipement a été testé et reconnu conforme aux limites de la classe A pour les équipements 
numériques,  conformément  à  la  section  15  des  Réglementations  FCC.  Ces  limites  sont  conçues 
pour  fournir  une  protection  raisonnable  contre  toutes  interférences  nuisibles  dans  un  milieu 
résidentiel. Cet équipement génère, utilise, et peut émettre de l’énergie de fréquence radio et, s’il 
n’est  pas  installé  et  utilisé  conformément  au  manuel  d’instruction,  peut  perturber  la  réception 
radio. Cependant, il n’est pas garanti que l’équipement ne produira aucune interférence dans une 
installation particulière. Si cet équipement cause des interférences nuisibles à la réception radio ou 
télévisée, qui peuvent être déterminées en l’éteignant et le rallumant, l’utilisateur est encouragé à 
essayer de remédier au problème en prenant les mesures suivantes: 
* Réorienter ou déplacer l’antenne réceptrice. 
* Augmenter la distance entre l’équipement et le récepteur. 
*  Connecter  l’équipement  à  une  prise  secteur  sur  un  circuit  différent  de  celui  utilisé  par  le 
récepteur. 
* Consulter le négociant ou un technicien radio/TV expérimenté. 
 

 

Caution: Any changes or modifications not expressly approved by the grantee of this device could 
void the user's authority to operate the equipment.

 

 

ATTETNION

: Tout changement ou modification non expressément approuvé par le concessionnaire 

de cet appareil pourrait annuler l'autorité de l'utilisateur à utiliser l'équipement.

 

Summary of Contents for EG5-1802-SFP Series





















Reviews: