background image

19 

Trouble Shooting 

 
● 

Verify you have the right power cord or adapter. Never use a power supply or adapter with a 
non-compliant DC output voltage or it will burn the equipment.

 

 
● 

Select the proper UTP or STP cable in order to construct the network. Use an unshielded twisted-
pair  (UTP)  or  shield  twisted-pair  (STP)  cable  for  RJ-

45  connections:  100Ω  Category  5e  for 

10M/100/1000Mbps.  Also  be  sure  that  the  length  of  any  twisted-pair  connection  does  not 
exceed 100 meters (328 feet).

 

 
● 

Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily monitored 
with the LED indicators which help to identity if any problems exist.

 

 

Please refer to the LED Indicators section for LED light indication.

 

 
● 

If the power indicator LED does not turn on when the power cord is plugged in, the user may 
have a problem with the power cord. Check for loose power connections, power losses or surges 
at the power outlet.

 

 

Please  contact  Leonton  for  technical  support  service,  if  the  problem  still  cannot  be 
resolved.

 

 

 

If the industrial switch LED indicators are normal and the connected cables are correct but the 

packets still cannot transmit, please check the system’s Ethernet devices’ configuration or status.

 

 
 
 
 
 
 
 
 

 

For any repair or maintenance needs, please contact us. 

LEONTON TECHNOLOGIES, CO., LTD 

9F-1, No.43, Fuxing Rd., Xindian Dist.,  

New Taipei City, 231,  

Taiwan 

TEL: +886 2 22183113 

FAX: +886 2 22187391 

Summary of Contents for CET2-0500 Series




















Reviews: