Lenze PROFINET 9400 Communications Manual Download Page 33

Page: 33 / 119

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

Commissioning

6.2

Configuring the PROFINET IO controller

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.2

Configuring the PROFINET IO controller

To enable communication with the Servo Drive 9400, you have to configure the IO controller first.

Configuration for device control

For the configuration of PROFINET, the current PROFINET device description file (XML) of the

E94AYCER communication module (PROFINET) has to be imported in the IO controller.
The device description file

GSDML-Vx.z-Lenze-9400PNabb-yyyymmdd.xml

can be found in the

download area at:

www.lenze.com

Defining the user data length

The user data length is defined during the initialisation phase of the I/O controller.
Servo Drives 9400 HighLine support the configuration of max. 32 process data words (max.

64 bytes).

Description of the device data base file

Wildcards in the file name "GSDML-Vx.z-Lenze-9400PNabb-yyyymmdd.xml"

Main version of the GSDML scheme used

Subversion of the GSDML scheme used

Major version of the software version

Minor version of the software version

yyyy

Year

Month

Day

Selection text

Process data

(with consistency)

Assigned

I/O memory

Safety module

PCD (

W) AR cons.

words

Safety (4W) AR

4 words

SM301

Safety (8W) AR

(

from SW version 3.00

onwards

)

8 words

SM302

= 1 ... 32 process data words

Summary of Contents for PROFINET 9400
























































































































Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands

Lenze PROFINET 9400, Communications Manual

Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands