Lenze POWERLINK E84DGDV Series Communications Manual Download

Page: 47 / 70

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

Parameter reference

Parameters relevant for POWERLINK communication

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C13004

Parameter | Name:

C13004 | 0x1030.5 MAC address

Data type: OCTET_STRING

Index: 11571

= 2D33

The code indicates the physical address (MAC address) of the POWERLINK interface of the Communication Unit.

When the Communication Unit is produced, the MAC address is assigned unequivocally worldwide and provides ad-

dressing on the lowest level.

Display range

(min. value | unit | max. value)

Subcodes

Info

C13004/1

MAC Address (octet string[6])

00-0A-86-xx-yy-zz

• 00-0A-86 = Lenze

• xx-yy-zz = consecutive number



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Summary of Contents for POWERLINK E84DGDV Series







































































Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands

Lenze POWERLINK E84DGDV Series, Communications Manual

Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands