Lenze POWERLINK E84DGDV Series Communications Manual Download Page 38

Page: 38 / 70

Diagnostics

LED status displays

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Diagnostics

POWERLINK communication faults can be diagnosed via the LEDs of the Communication Unit.

9.1

LED status displays

LED

Colour

Status

Description

Activity

green

Off

The Communication Unit is not active on the fieldbus or is in the

"INIT" state.

blinking

EPL network is in the initialisation phase.

EPL status: NMT_CS_PREOPERATIONAL_1

blinking

EPL network is in the initialisation phase with cyclic traffic.

EPL status: NMT_CS_PREOPERATIONAL_2

blinking

EPL node is waiting for the start signal.

EPL status: NMT_CS_READY_TO_OPERATE

blinking

The EPL node has not found a managing node and is in

EPL status: NMT_CS_BASIC_ETHERNET

blinking

EPL node is in the "Stopped" status (waiting for disconnection).

EPL status: NMT_CS_STOPPED

EPL node is in the operating phase.

EPL status: NMT_CS_OPERATIONAL

Activity

ERR

RUN

50 ms

200 ms

Summary of Contents for POWERLINK E84DGDV Series







































































Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands

Lenze POWERLINK E84DGDV Series, Communications Manual

Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands