Lenze ECS series Operating Instructions Manual Download Page 460 | Manualshive

Page: 460 / 484

background image

Appendix

Communication with MotionBus/system bus (CAN)
Addressing of the parameter and process data objects

460

EDBCSXS064 EN 4.0

13.4.5

Addressing of the parameter and process data objects

The CAN bus system is based on a message−oriented data exchange between a transmitter
and many receivers. Thus, all nodes can transmit and receive messages at the same time.

The identifier in the CAN telegram ˘ also called

COB−ID (Communication Object Identifier)

controls which node is to receive a transmitted message. With the exception of the
network management (NMT) and the sync telegram (Sync) the identifier contains the
node address of the drive besides the basic identifier:

Identifier (COB−ID) = basic iden adjustable node address (node ID)

The basic identifier is preset with the following values:

Object

Direction

Basic identifier

to the

ECS module

from the

ECS module

dec

hex

NMT

0

0

Sync

128

80

PDO1

(Process data channel 1)

RPDO1

XCAN1_IN
CAN1_IN
CANaux1_IN

X

512

200

TPDO1

XCAN1_OUT
CAN1_OUT
CANaux1_OUT

X

384

180

PDO2

(Process data channel 2)

RPDO2

XCAN2_IN
CAN2_IN
CANaux2_IN

X

640

280

TPDO2

XCAN2_OUT
CAN2_OUT
CANaux2_OUT

X

641

281

PDO3

(Process data channel 3)

RPDO3

XCAN3_IN
CAN3_IN
CANaux3_IN

X

768

300

TPDO3

XCAN3_OUT
CAN3_OUT
CANaux3_OUT

X

769

301

SDO1

(Parameter data channel 1)

X

1536

600

X

1408

580

SDO2

(Parameter data channel 2)

X

1600

640

X

1472

5C0

Node guarding

X

1792

700

Display of the resulting identifiers

The display code for the resulting identifiers is for the

ƒ

Interface X1 (AIF) C2355.

ƒ

Interface X4 (CAN) C0355.

ƒ

Interface X14 (CAN−AUX) C2455.

Here, no values can be entered.

ƒ

General addressing (

460):

Identifier (COB−ID) = basic iden adjustable node address (node ID)

ƒ

Individual addressing (

Identifier (COB−ID) = 384 + ID offset (C0354 or C2454)

«
...
458
459
460
461
462
...
»

Summary of Contents for ECS series





































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECS series

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Samson Pages: 20

Brand: Acclaim Lighting Pages: 32

Brand: LAS Pages: 6

Brand: Paradox Pages: 32

TBEN-L 8IOL Series

Brand: turck Pages: 148

APEXpy 07-37A2-2111/ 520Series

Brand: Bartec Pages: 98

Brand: Reer Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: ACS Pages: 2

Brand: Litex Pages: 1

Brand: Scanreco Pages: 48

Brand: DMP Electronics Pages: 56

Brand: REMKO Pages: 20

Infi 90 IMCPM03

Brand: Bailey Pages: 61

SEPCOM SIP BED Easy

Brand: WAMGROUP Pages: 52

Brand: DH Instruments Pages: 30

Brand: Brooks Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands