manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 44 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 44

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

44

6

Commissioning

6.4

Establishing an online connection via EtherNet/IP with the Lenze »Engineer«

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

6.4

Establishing an online connection via EtherNet/IP with the Lenze »Engineer«

[6-1]

Example setup: Allen-Bradley CompactLogix controller with Servo Drives 9400

For an online connection between the »Engineer« and the drive, the drive must have an IP address

(see 

Setting the IP configuration of the Servo Drive 9400

 (

37)

).

Note!

• In order to ensure perfect operation of cyclic EtherNet/IP communication, online 

access with the »Engineer« should be executed via an IEEE 802.1Q-capable switch.

• The IEEE 802.1Q-capable switch integrated in the communication module can 

manage cyclic EtherNet/IP communication preferentially to normal TCP/IP 

communication. In the case of EtherNet/IP this is effected using the VLAN 

identification in the Ethernet frame (adjustable in 

C13021

/ 

C14021

).

• If the redundancy protocol DLR (Device Level Ring) is used, the switch also must be 

DLR-compliant.

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments