Lenze E84AYCEC Communications Manual Download Page 43

Page: 43 / 90

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

Commissioning

Optimisation of networks

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.6

Optimisation of networks

SDO bandwidth

The SDO channel width (

C13075

) is the size of the asynchronous channel used for parameter setting

and diagnostics. A higher value improves the transmission of large amounts of data (e.g. parameter

downloads) and at the same time reduces the number of possible nodes.

Maximum time for device search

During the device search, the managing node has to wait until all controlled nodes have been found.

• Unless all controlled nodes are available in the defined EPL cycle time, the "EPL_BOOTUP_1" er-

ror message is generated. The managing node remains in this status.

• If the managing node has found all controlled nodes, it starts the network.

Due to machine or system-specific switch-on sequences, it may be required to adapt the following

EPL objects:

• CN object

0x1F99

: NMT_CNBasicEthernetTimeout_U32 (

C13078

)

• MN object

0x1F89

: NMT_BootTime_REC



Note!

The channel bandwidth should only be increased if the network is below capacity limit.



Note!

In order to avoid a too quick change to the "

, the value of the

0x1F99

object (NMT_CNBasicEthernetTimeout_U32) must be higher than the value of

the

0x1F89

object (NMT_BootTime_REC) which is the case by default.

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands