Lenoxx TT650, Instruction Manual

Page: 4 / 11

4
FOR 10 MINUTES. AFTER 9-10 MINUTUE SNOOZE INTERVAL, ALARM WILL BE ACTIVE AGAIN. SNOOZE CAN
BE USED FOR REPEATEDLY WITHIN THE 1-HOUR ALARM ACTIVE INTERVAL.
TIMER FUNCTION
1. PRESS THE POWER BUTTON TILL THE STANDBY INDICATOR LIGHT OFF. UNIT IS TURNING FROM
STANDBY MODE TO OPERATION MODE.
2. WHEN THE UNIT IS TURNED ON, PRESS SLEEP BUTTON REPEATEDLY TO CHOOSE THE SLEEP TIME
MINUTES FROM 90>80>70
…..>10 OFF.
3. SLEEP TIME SETTING IS STORED WHEN THE
“SLEEP” ICON LIGHTS UP ON THE DISPLAY.
WHEN THE SLEEP TIME MINUTES IS OVER, UNIT WILL BE SWITCHED TO STANDBY MODE AUTOMATICALLY.
LISTENING TO RADIO
RADIO TUNING
1. PRESS FUNCTION BUTTON REPEATED TO SELECT
“TUNER” MODE.
2. SELECT THE DESIRED BAND BY BAND BUTTON (AM OR FM).
3. TUNE TO THE REQUIRED STATION BY PRESSING AND HOLDING SKIP UP OR SKIP DOWN
BUTTON FOR 1-2 SECONDS, AND THEN RELEASE.
4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.
MANUAL PRESET RADIO STATIONS
1. WHEN THE DESIRED RADIO STATION IS FOUND, PRESS MODE BUTTON, PROGRAM NUMBER WILL BE
FLASHING.
2. PRESS PRESET UP OR PRESET DOWN TO CHOOSE THE PROGRAM NUMBER FOR STORING THE
DESIRED RADIO STATION.
3. PRESS MODE BUTTON AGAIN TO CONFIRM, PROGRAM NUMBER WILL STOP TO FLASH.
4. REPEAT STEP 2 & 3 UNTIL ALL DESIRED RADIO STATIONS IS BEING FOUND AND STORED
5. PRESS
PRESET UP OR PRESET DOWN TO CHOOSE THE PRESET RADIO STATIONS.
6. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
AUTO PRESET RADIO STATIONS
1. DURING RADIO MODE, PRESS THE TUNER SCAN BUTTON , THE UNIT WILL AUTOMATICLLY SCAN THE
RADIO FREQUENCY. WHEN THE CLEAR SIGNAL IS FOUND, IT WILL AUTOMATICALLY STORE THE RADIO
STATION, STARTING FROM PROGRAM NUMBER 1.
2. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
FM & FM-STEREO RECEPTION

PRESS
“FM ST.” BUTTON ON THE REMOTE CONTROL TO SELTECT FM MONO OR FM STEREO MODE.
WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
 “ST” ICON LIGHT UP ON THE DISPLAY TO SHOW FM STEREO MODE IS RECEIVING.
HINTS FOR BETTER RECEPTION
1. AM: THERE IS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATING OR
RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
2. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
1. PRESS FUNCTION BUTTON REPEATED TO SELECT
“TUNER” MODE.
2. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
3. PRESS THE
REC BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE.
4. PRESS SKIP UP OR SKIP DOWN BUTTON TO SELECT DESIRED MODE (USB OR SD) FOR
ENCODING. THEN PRESS THE REC BUTTON AGAIN TO CONFIRM. AND THE SYSTEM IS STARTING THE
ENCODING MODE AFTER FEW SECONDSS.
5. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
6. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
7. TO FINISH ENCODING, PRESS
STOP BUTTON AND DISPLAY WILL SHOW
“END” AND RETURN TO
“ TUNER” MODE.
REMARK:-
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLAYING TIME OF FM OR FM-ST
RADIO
- THE RECORDING FORMAT IS PRESET AT
– MP3 BIT RATE : 128 KBPS
- DURING FM & FM-STEREO RADIO ENCODING, RADIO FREQEUNCY IS FXIED AND CANNOT BE TUNED