background image

 

 

heater, as this may result in electric shock, fire, or damage to the heater.   

Do not drop or hit/impact the heater. 

Do not use the appliance in areas where petrol, paints or other flammable 
substances are used or stored. 

Do not plug the item in before it is set on castors. 

Always position the appliance with the mains plug in an accessible position and 
avoid the use of an extension cables as they may overheat and create a potential 
fire risk. 

Always ensure the heater is plugged into a suitable socket. 

Avoid the use of an extension cord and/or power board as this may overheat and 
cause a risk of fire. 

Always ensure the heater is plugged into a suitable socket. 

Be sure that no other appliances are in use on the same electrical circuit as this 
product as an overload can occur. 

To disconnect heater, turn controls to OFF, then remove plug from socket. Do not 
unplug by pulling on the power cable. 

Always unplug the unit and ensure the unit is completely cold before moving, 
cleaning or storing. 

This heater is intended for domestic use only and should not be used 
commercially for contract purposes. Any alternative use, not recommended by 
the manufacturer, may result in fire, electric shock, or injury to persons. 

The use of attachments on the heater is not recommended. 

If the supply cord is damaged, it must be replaced by the manufacturer, its 
service agent or similarly qualified persons in order to avoid a hazard.   

The heater must not be located immediately below a socket outlet. 

Do not use this heater with a programmer, timer, separate remote-control system 
or any other device that switches the heater on automatically, since a fire risk 
exists if the heater is covered or position incorrectly. 

Pay attention that, no combustible material due to wind or other environmental 
influences covers or obstructs the appliance, such as curtains, marquees, flags, 
plastic foil etc. 

This heater is filled with a precise quantity of special oil. 

Repairs requiring the opening of the oil container are only to be made by the 

Summary of Contents for H200









Reviews: