background image

FEATURES:  

Safe & stable 

Low centre of gravity 

Durable material 

Indoor or outdoor play 

No batteries, gears or pedals 

HOW IT WORKS: 

1.

 

Place the ride on swing car onto a smooth, flat surface. 

2.

 

Sit with the feet on the footrests. Lean slightly forward and grip the steering wheel. 

3.

 

To propel the car forward, turn the steering wheel back and forth continuously. To go in reverse, 
rotate the steering wheel 180 degrees. 

4.

 

To bring the ride on swing car to a stop, stop turning the wheel, wait for the car to slow, and 
come to a stop. 

SAFETY INFO: 

1.

 

When unpacking the ride on swing car, properly dispose of all plastic wrappings. 

2.

 

Adult supervision is required at all times. 

3.

 

Failure to follow the instructions may affect the safety of children. 

4.

 

This product is designed for use by children from 3 years to 6 years of age. 

5.

 

Protective equipment such as a helmet is recommended (protective equipment is not included). 

6.

 

Assembly must be completed by an adult. 

7.

 

Each time before use, ensure that all removeable parts and fasteners are firmly in place. 

8.

 

Only one child can use this at a time. 

9.

 

A child who is riding is not to be pushed. 

10.

 

Do not allow a child to stand on the ride-on. 

11.

 

Do not let children ride in the street, anywhere dangerous including stairs, doorsteps, steep 
slopes, streets/roads, vehicle traffic, next to bodies of water and away from other obstacles. Use 
during day light hours or in an illuminated area is advised to avoid accidents in the dark. 

12.

 

Do not drive on long or wet grass, mud, soft ground, gravel or sand. 

13.

 

It is not recommended for use on wooden floors. The wheels may damage some floors. 

14.

 

The maximum carrying capacity is 30kg. 

ASSEMBLY: 

Included parts: 

1.

 

Body 

2.

 

Steering wheel assembly 

3.

 

Front wheel assembly with foam sheath 

4.

 

Rear right wheel (A), Rear left wheel (B) 

5.

 

Steering wheel cap 

Tools required (not included): rubber mallet, 20mm socket wrench. 

 

 

Summary of Contents for 8821









Reviews: