manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

Automatically contact Service

If this field is set to

Yes

, and you have enabled Electronic Service Agent (ESA), Lenovo Support will be

notified automatically if the event is generated.

While you wait for Lenovo Support to call, you can perform the recommended actions for the event.

User response

The actions that you should perform to solve the event.

Perform the steps listed in this section in the order shown until the problem is solved. After you perform
all of the actions that are described in this field, if you cannot solve the problem, contact Lenovo Support.

Note:

This list includes error codes and messages that might not apply to this machine type and model.

Below is the list of IMM2 error messages and suggested actions to correct the detected server
problems. For more information about IMM2, see the

Integrated Management Module II User's Guide

at http://publib.boulder.ibm.com/infocenter/ systemx/documentation/topic/ com.lenovo.sysx.imm2.doc/
printable_doc.html.

IMM Events that automatically notify Support

You can configure the IBM Flex System Manager or the CMM to automatically notify Support (also known as

call home

) if certain types of errors are encountered. If you have configured this function, see the table for

a list of events that automatically notify Support.

Table 39. Events that automatically notify Support

Event ID

Message String

Automatically
Notify Support

40000086-00000000

Test Call Home Generated by user [arg1].

Yes

40000087-00000000

Manual Call Home by user [arg1]: [arg2].

Yes

80010202-0701ffff

Numeric sensor [NumericSensorElementName] going low
(lower critical) has asserted. (CMOS Battery)

Yes

80010902-0701ffff

Numeric sensor [NumericSensorElementName] going
high (upper critical) has asserted. (SysBrd 12V)

Yes

806f0021-2201ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (No Op ROM
Space)

Yes

806f0021-2582ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (All PCI Error)

Yes

806f0021-2c01ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (Mezz Error)

Yes

806f0021-3001ffff

Fault in slot [PhysicalConnectorSystemElementName] on
system [ComputerSystemElementName]. (PCI 1)

Yes

806f0108-0a01ffff

[PowerSupplyElementName] has Failed. (Power Supply 1)

Yes

806f0108-0a02ffff

[PowerSupplyElementName] has Failed. (Power Supply 2)

Yes

806f010c-2001ffff

Uncorrectable error detected for
[PhysicalMemoryElementName] on Subsystem
[MemoryElementName]. (DIMM 1)

Yes

806f010c-2002ffff

Uncorrectable error detected for
[PhysicalMemoryElementName] on Subsystem
[MemoryElementName]. (DIMM 2)

Yes

346

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Qlogic iSR6200 Quick Start Manual preview
iSR6200
Brand: Qlogic Pages: 20
Wyse C00LE Quick Start Manual preview
C00LE
Brand: Wyse Pages: 6
IBM BladeCenter JS20 Installation And User Manual preview
BladeCenter JS20
Brand: IBM Pages: 132
Supermicro SuperWorkstation 740A-T User Manual preview
SuperWorkstation 740A-T
Brand: Supermicro Pages: 138
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print... User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...
Brand: 3Com Pages: 94
Belkin F1UP0002 Quick Installation Manual preview
F1UP0002
Brand: Belkin Pages: 2
Sun Microsystems Sun Fire Netra 1280 Product Notes preview
Sun Fire Netra 1280
Brand: Sun Microsystems Pages: 10
Epson C823781 Software Installation Manual preview
C823781
Brand: Epson Pages: 28
Epson EpsonNet 802.11b Product Support Bulletin preview
EpsonNet 802.11b
Brand: Epson Pages: 30
Epson Stylus C80WN - Ink Jet Printer Hardware preview
Stylus C80WN - Ink Jet Printer
Brand: Epson Pages: 1
Epson C823781 Administrator'S Manual preview
C823781
Brand: Epson Pages: 258
Epson C82378 Administrator'S Manual preview
C82378
Brand: Epson Pages: 280
Fujitsu B23Q8WD-G-01-J Hardware Manual preview
B23Q8WD-G-01-J
Brand: Fujitsu Pages: 26
Fujitsu FUTRO S450 Operating Manual preview
FUTRO S450
Brand: Fujitsu Pages: 56
Fujitsu FD-1000ST User Manual preview
FD-1000ST
Brand: Fujitsu Pages: 36
Fujitsu FUTRO S550 Operating Manual preview
FUTRO S550
Brand: Fujitsu Pages: 61
Fujitsu BS2000 Operating Manual preview
BS2000
Brand: Fujitsu Pages: 30
Fujitsu ETERNUS DX Disk Configuration Manual preview
ETERNUS DX Disk
Brand: Fujitsu Pages: 85

Brands by name

Popular brands

Load more brands