manualshive.com logo in svg

Lenovo x3650 M4 BD 5466, Installation And Service Manual

The Lenovo x3650 M4 BD 5466 is a high-performance server featuring an impressive storage capacity. Ensure smooth operations by referring to the comprehensive Product Manual, available for free download at manualshive.com. Access the manual to maximize the potential of this exceptional product.

Share
Download
background image

•

201-901-003 : Standalone Memory Test Failed

Memory Diagnostics Test Failed.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Perform the actions mentioned one at a time and try the test after each action.

2. If the problem remains, contact your technical-service representative.

3. Turn off the system and disconnect it from power. Wait for 45 seconds. Reseat DIMM(s).

Reconnect it to power.

4. Make sure that DSA and BIOS/uEFI are at the latest level.

5. Replace any DIMMS(s) mentioned in error, one by one.

6. Make sure that all DIMMs are enabled in the Configuration/Setup Utility program.

7. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory stress test results

The following messages can result when you run the memory stress test.

Test results for the DSA memory stress test

The following messages can result when you run the DSA memory stress test.

•

202-000-000 : MemStr Test Passed

Test Passed.

Recoverable

No

Severity

Event

1152

Lenovo System x3650 M4 Installation and Service Guide

Summary of Contents for x3650 M4 BD 5466







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M4 BD 5466

Supero SUPERSERVER 6027R-TRF User Manual preview
SUPERSERVER 6027R-TRF
Brand: Supero Pages: 102
Supermicro SuperServer 5039MD18-H8TNR User Manual preview
SuperServer 5039MD18-H8TNR
Brand: Supermicro Pages: 134
N-Tron ESERV-11T User Manual preview
ESERV-11T
Brand: N-Tron Pages: 55
Shenzhen JingFeng HDM-05 User Manual preview
HDM-05
Brand: Shenzhen JingFeng Pages: 11
AIC SB401-MN User Manual preview
SB401-MN
Brand: AIC Pages: 88
NMS Communications Vision VS 5000 Installing preview
Vision VS 5000
Brand: NMS Communications Pages: 22
IBM System x3650 M4 BD Type 5466 Installation And Service Manual preview
System x3650 M4 BD Type 5466
Brand: IBM Pages: 786
Quatech WLNG-AN-DP500 Series Reference Manual preview
WLNG-AN-DP500 Series
Brand: Quatech Pages: 120
QUANTA QSSC-S99K 2U User Manual preview
QSSC-S99K 2U
Brand: QUANTA Pages: 177
IBM eServer xSeries 335 Type 8676 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 335 Type 8676
Brand: IBM Pages: 178
Fujitsu PRIMERGY RX300 S6 Options Manual preview
PRIMERGY RX300 S6
Brand: Fujitsu Pages: 132
Fujitsu PRIMERGY RX300 S5 Operating Manual preview
PRIMERGY RX300 S5
Brand: Fujitsu Pages: 112
Fujitsu PRIMERGY RX2540 M4 Operating Manual preview
PRIMERGY RX2540 M4
Brand: Fujitsu Pages: 86
Fujitsu PRIMERGY RX2540 M6 Operating Manual preview
PRIMERGY RX2540 M6
Brand: Fujitsu Pages: 121
Fujitsu PRIMERGY RX4770 M6 Upgrade And Maintenance Manual preview
PRIMERGY RX4770 M6
Brand: Fujitsu Pages: 468
Fujitsu PRIMERGY RX2540 M1 Operating Manual preview
PRIMERGY RX2540 M1
Brand: Fujitsu Pages: 92
Fujitsu PRIMERGY RX2540 M5 Operating Manual preview
PRIMERGY RX2540 M5
Brand: Fujitsu Pages: 112
Fujitsu PRIMERGY RX2540 M4 Upgrade And Maintenance Manual preview
PRIMERGY RX2540 M4
Brand: Fujitsu Pages: 639

Brands by name

Popular brands

Load more brands