Lenovo x3250 m6 Installation And Service Manual Download Page 105

Page: 105 / 696

Step 1.

Align the air baffle tabs

with the notches in the server fan cage. Then, lower the air baffle into the

server and press the air baffle down until it is securely seated.

Figure 17. Air baffle installation

Step 2.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Removing the security bezel

To remove the security bezel, do the following:

Step 1.

Turn off the server.

Step 2.

Use the key to unlock the security bezel to the open position.

000000000000000

0000000000

Figure 18. Unlocking the security bezel

Chapter 7

Removing and installing server components

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands