manualshive.com logo in svg

Lenovo tihnkserver rd330, Hardware Maintenance Manual

Share
Download
Lenovo tihnkserver rd330 Hardware Maintenance Manual Download Page 47

• If you are using a ThinkServer RAID 700 Adapter, do the following:

1. Use one mini-SAS to mini-SAS signal cable. Connect the mini-SAS connector

3

on one end of the

cable to the ports 3-0 on the RAID card. Then, connect the mini-SAS connector

4

on the other end

of the cable to the mini-SAS ports 0-3 on the backplane.

2. If your server has more than four hard disk drives installed, use the other mini-SAS to mini-SAS

signal cable. Connect the mini-SAS connector

1

on one end of the cable to the ports 7-4 on the

RAID card. Then, connect the mini-SAS connector

2

on the other end of the cable to the mini-SAS

ports 4-5 on the backplane.

Refer to the following topics for information about the connector locations:

•

“Hot-swap hard disk drive backplane” on page 29

•

“RAID card” on page 27

•

“System board components” on page 33

System board components

The following illustration shows the component locations on the system board.

Figure 22. System board components

1

Front panel connector

17

Riser card assembly 1 slot

2

Internal USB connector 1

18

Riser card assembly 2 slot

3

Internal USB connector 2

19

Redundant power supply connector 1

Chapter 3

.

Product overview

33

Summary of Contents for tihnkserver rd330







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands