Lenovo ThinkSystem ST550 Setup Manual Download Page 99

Page: 99 / 136

Step 1. If there is a power-supply-bay filler installed, remove it.

Important:

To ensure proper cooling during normal server operation, both of the power supply

bays must be occupied. This means that each bay must have a power supply installed; or one has
a power supply installed and the other has a power-supply filler installed.

Figure 57. Hot-swap power supply filler removal

Step 2. Slide the new hot-swap power supply into the bay until it snaps into position.

Figure 58. Hot-swap power supply installation

Install a front fan

Use this information to install a front fan.

Static Sensitive Device

Ground package before opening”

on page 59

Chapter 3

Server hardware setup

Summary of Contents for ThinkSystem ST550









































































































































Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands

Lenovo ThinkSystem ST550, Setup Manual

Search results

Summary of Contents for ThinkSystem ST550

Reviews:

Related manuals for ThinkSystem ST550

Brands by name

Popular brands