Lenovo thinksystem SN850 7X15 Setup Manual Download Page 28

Page: 28 / 88

System-board connectors

Use this information to locate compute node system-board components and connectors for optional
devices.

The following illustration shows the system-board components, including connectors for user-installable
optional devices, in the compute node.

Figure 7. System board connectors

Table 7. System board connectors

DIMM slot 25 – 30

Processor socket 2

Processor socket 3

DIMM slot 19 – 24

DIMM slot 1 – 6

Processor socket 4

Processor socket 1

DIMM slot 43 – 48

I/O expansion 1 connector

Switch blocks

I/O expansion 2 connector

Light path diagnostics

DIMM slot 7 – 18

2.5-inch drive backplane connector

I/O expansion 3 connector

CMOS battery slot

Fabric connector slot

DIMM slot 31 – 42

ThinkSystem SN850 Compute Node Setup Guide

Summary of Contents for thinksystem SN850 7X15

























































































Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands

Lenovo thinksystem SN850 7X15, Setup Manual

Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands