Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 117

Page: 117 / 246

a. Align the plastic boards on the top and bottom sides of the direct cooling air baffle with the small

gaps

in the chassis. Ensure that the handle of the direct cooling air baffle faces toward the front of

the chassis.

Figure 17. Aligning the plastic boards with the small gaps

b. Slide the direct cooling air baffle into the chassis until it is secured firmly.

Note:

If necessary, adjust the position of the direct cooling air baffle slightly to avoid any interference

with other components in the chassis.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 210.

Device in a flex bay

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Depending on your computer model, the following devices might be installed in the flex bays:

• Flex module

Chapter 9

Hardware removal and installation

109

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 117 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: