Lenovo ThinkStation P500 Hardware Maintenance Manual Download Page 134

Page: 134 / 232

Replacing the front fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

Note:

The front fan assembly is only available on some models.

To replace the front fan assembly, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 111.

3. Pull the front fan assembly by the handle to slide it out of the computer chassis.

Note:

When you slide out the front fan assembly, avoid pulling the front fan assembly cable.

Figure 41. Removing the front fan assembly

4. Disconnect the front fan assembly cable from the front fan connector on the system board.

5. Connect the cable of the new front fan assembly to the front fan connector on the system board. See

“Locating parts on the system board” on page 35.

128

ThinkStation P500 and P700 Hardware Maintenance Manual

Summary of Contents for ThinkStation P500









































































































































































































































Search results

Summary of Contents for ThinkStation P500

Reviews:

Lenovo ThinkStation P500, Hardware Maintenance Manual, Page: 134 / 232

Search results

Summary of Contents for ThinkStation P500

Reviews: