manualshive.com logo in svg

Lenovo ThinkCentre 5110, Maintenance Manual

Share
Download
Lenovo ThinkCentre 5110 Maintenance Manual Download Page 93

12. Lift the main bracket up a little bit so that the LCD panel detaches from the main bracket, and you can

gently pull out the microprocessor fan assembly cable connectors through the hole in the main bracket.

13. Lift the microprocessor fan assembly and cables up and out of the main bracket.

Installing a microprocessor fan assembly

To install a microprocessor fan assembly, do the following:

1. Reinstall the four screws that attach the new microprocessor fan assembly to the main bracket.

2. Lift the main bracket up so that you can route the microprocessor fan assembly cables through the hole

in the main bracket. Connect the microprocessor fan assembly cables to the system board connectors.

3. Route the microprocessor fan assembly cables so that they will not be pinched by the system board

shielding.

4. Reinstall the four screws that attach the LCD panel to the main bracket.

Chapter 9

.

Replacing FRUs

87

Summary of Contents for ThinkCentre 5110

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands