Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 158 | Manualshive

Page: 158 / 296

background image

Complete the following steps to remove a hot-swap drive.

Watch the procedure

. A video of the installation process is available:

•

•

Step 1. Make a note of the bay where the drive is installed: drives must be installed in the bay from which

they were removed.

Step 2. Remove the drive.

a. Slide the release latch to open the drive tray handle.

Figure 80. Opening the handle of a 3.5-inch hot-swap drive

b. Grasp the handle and slide the drive out of the drive bay.

Figure 81. 3.5-inch hot-swap drive removal

After you remove the hot-swap drive:

1. Install a replacement hot-swap drive or filler in the empty drive bay.
2. If you are instructed to return the drive assembly, follow all packaging instructions, and use any

packaging materials for shipping that are supplied to you.

Install a hot-swap drive

Insert the hot-swap drive in its bay and close the latch handle to lock the drive in place. Hot-swap devices

can be installed while the server is powered on.

” on page 89 “

148

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
156
157
158
159
160
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Zonet Pages: 33

Brand: ioCorp Pages: 18

Brand: i3 International Pages: 2

Brand: Eaton Pages: 2

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

847620U - Netfinity 3000 - 20U

Brand: IBM Pages: 270

Brand: IBM Pages: 100

BladeCenter PS703

Brand: IBM Pages: 198

SuperServer 5013G-M

Brand: Supero Pages: 104

Brand: Asus Pages: 186

Brand: Intergraph Pages: 102

ProLiant DL380 Gen10 Plus

Brand: HP Pages: 16

Brand: HP Pages: 43

ProLiant DL385p Generation 8

Brand: HP Pages: 57

ProLiant DL380 Generation9

Brand: HP Pages: 76

ProLiant DL360p Gen8

Brand: HP Pages: 4

ProLiant DL380 Generation 6

Brand: HP Pages: 50

ProLiant DL360p G8

Brand: HP Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands