Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 140

Page: 140 / 296

Front bezel replacement

Use the following procedures to remove and install the front bezels.

Remove the front bezel

Remove each front bezel by pressing the release tabs and pulling the bezel from the front of the server.

Before you remove the front bezel, make sure that you remove the front cover. See “Remove the front cover”
on page 131.

Complete the following steps to remove the front bezel:

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

Figure 68. Front bezel removal

Step 1. Press the release tabs on each front bezel.
Step 2. Pull the bezel forward and remove it from the server.

Install the front bezel

Install each front bezel by sliding the bezel into position and pressing until it is fully seated.

Complete the following steps to install the front bezel:

Watch the procedure

. A video of the replacement process is available:

•

YouTube

•

Youku

130

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands

Lenovo ThinkAgile VX 4-Socket 4U Certified Node, User Manual

Search results

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node

Reviews:

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brands by name

Popular brands