Lenovo ThinkAgile CP 4000 Series Upgrade Manual Download Page 59

Page: 59 / 68

Step 4. Pull the slide forward and insert the pins and the latch into the flange holes at the front of the rack.

Figure 20. Left slide front installation

Step 5. Repeat steps

through

to install the other slide rail. Ensure that each slide rail is securely

engaged in the flange by:

1. Inspecting to confirm that the hook has caught in the rack.

2. Moving the slide rail backward and forward to ensure that it does not pop out.

Step 6. Insert a M5 screw and washer into the rear bracket of each slide rail, and then fasten the two M5

screws to secure the slide rails to the rack flanges.

Figure 21. Securing the compute block slide rails

The installation of the compute block slide rails in a rack is now complete.

To continue with the installation of the ThinkAgile CP compute block, follow these steps: Install the compute
enclosure

Chapter 4

Compute block capacity upgrade

Summary of Contents for ThinkAgile CP 4000 Series





































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Upgrade Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands