manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 64

• Make sure that cables are not pinched by the server components.

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation”
on page 94.

Installing an adapter in the rear two hard-disk-drive kit

Use this information to replace an adapter in the rear two hard-disk-drive kit.

You can only install SeveRAID-H1110 adapter in the rear two hard-disk-drive kit.

To install an adapter, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Step 3.

Remove the server cover (see “Removing the cover” on page 37).

Step 4.

Remove the rear two hard-disk-drive kit (see “Removing the rear two hard-disk-drive kit” on
page 224).

Step 5.

Follow the cabling instructions, if any come with the adapter. Route the adapter cables before
you install the adapter.

Attention:

• When you route cables, do not block any connectors or the ventilated space around any of

the fans.

• Make sure that cables are not routed on top of components under the rear two hard-disk-drive

kit.

• Make sure that cables are not pinched by the server components.

Step 6.

Align the adapter with the slot on the rear two hard-disk-drive kit.

Step 7.

Press the adapter firmly into the slot on the rear two hard-disk-drive kit.

0000

0000

0000

0000

00000000

00000000

00000000

00000000

Adapter

Adapter
connector

Expansion-slot
cover

Bracket

Rear two hard-disk-drive kit

Figure 37. Adapter installation

Step 8.

Replace the rear two hard-disk-drive kit in the server (see “Replacing the rear two hard-disk-drive
kit” on page 225).

If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation”
on page 94.

52

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands