manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 276

0000

0000

0000

0000

0000

0000

0000

0000

0000

1.8-inch
filler panel

8x1.8-inch
drive backplane
assembly

Figure 185. Backplane assembly installation

Step 5.

Slide the drive backplane assembly into the slot until it clicks into place.

Step 6.

Connect the combination power/configuration cable to the connectors on the backplane assembly;
then connect the signal cables to the backplane assembly (as shown in the illustration).

Note:

You can reconnect the cables to the drive backplane before installing the backplane onto the

cage or you can connect the cables after you install the backplane, if that is easier for you.

Step 7.

Reinstall the drives that you removed from the old assembly into the new drive backplane assembly
(see “Replacing a hot-swap drive” on page 211).

Step 8.

Install the drive filler panel.

Step 9.

Install the cover (see “Replacing the cover” on page 196).

Step 10. Slide the server into the rack.

Step 11. Reconnect the power cords and any cables that you removed.

Step 12. Turn on the peripheral devices and the server.

Removing a USB embedded hypervisor flash device

Use this information to remove a USB embedded hypervisor flash device.

To remove a USB hypervisor flash device, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Remove the flash device:

264

Lenovo System x3650 M4 HD Installation and Service Guide

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands