manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 209

0

0

0

0

0

0

0

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

000000000000

Cover-release
latch

1

2

Figure 118. Cover installation

Step 6.

Slide the server all the way into the rack until it latches.

Step 7.

Reconnect the external cables and power cords.

Removing the bezel

Use this information to remove the bezel.

To remove the bezel, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Remove all the cables that are connected to the front of the server.

Step 3.

Remove the screws from the bezel.

Note:

Use the hex screw driver to remove the screws.

Chapter 6

.

Removing and replacing components

197

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands