manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

Step 5.

Align the memory module with the connector on the ServeRAID adapter and push it into the
connector until it is firmly seated.

ServeRAID adapter

ServeRAID 
memory module

Retention 
bracket

Figure 117. ServeRAID memory module installation

Step 6.

Reinstall the ServeRAID SAS/SATA controller (see “Replacing a ServeRAID SAS/SATA controller”
on page 185).

Step 7.

Reconnect the power cords and any cables that you removed.

Step 8.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 9.

Slide the server into the rack.

Step 10. Turn on the peripheral devices and the server.

Removing a thermal kit (hot-swap fan)

Use this information to remove a thermal kit (hot-swap fan).

Attention:

It is not necessary to disconnect the power when removing the hot-swap fan. To ensure proper

server operation, replace a failed hot-swap fan within 30 seconds.

To remove a hot-swap-fan, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Remove the cover (see “Removing the cover” on page 119).

Chapter 5

.

Removing and replacing components

193

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

NEC Univerge SV8100 Information Sheet preview
Univerge SV8100
Brand: NEC Pages: 2
Moxa Technologies ioLogik W5300 Series User Manual preview
ioLogik W5300 Series
Brand: Moxa Technologies Pages: 177
Edimax PS-1208MFg User Manual preview
PS-1208MFg
Brand: Edimax Pages: 93
Novell NETWARE 6 Manual preview
NETWARE 6
Brand: Novell Pages: 152
IBM BladeCenter HS21 1885 Problem Determination And Service Manual preview
BladeCenter HS21 1885
Brand: IBM Pages: 140
Cabletron Systems CSMIM2-16 Installation Manual preview
CSMIM2-16
Brand: Cabletron Systems Pages: 100
ORiNG IDS-5042 Series User Manual preview
IDS-5042 Series
Brand: ORiNG Pages: 67
Supermicro SuperServer 1029P-MT User Manual preview
SuperServer 1029P-MT
Brand: Supermicro Pages: 123
Fujitsu PRIMERGY BX620 S5 Options Manual preview
PRIMERGY BX620 S5
Brand: Fujitsu Pages: 50
Fujitsu PRIMERGY BX620 S4 Operating Manual preview
PRIMERGY BX620 S4
Brand: Fujitsu Pages: 81
Fujitsu PRIMERGY BX900 S1 Service Supplement Manual preview
PRIMERGY BX900 S1
Brand: Fujitsu Pages: 46
Fujitsu PRIMERGY BX620 S6 Options Manual preview
PRIMERGY BX620 S6
Brand: Fujitsu Pages: 56
Fujitsu Primergy BX920 S4 Operating Manual preview
Primergy BX920 S4
Brand: Fujitsu Pages: 66
Fujitsu PRIMERGY BX920 S2 Options Manual preview
PRIMERGY BX920 S2
Brand: Fujitsu Pages: 70
Fujitsu PRIMERGY BX920 S2 Operating Manual preview
PRIMERGY BX920 S2
Brand: Fujitsu Pages: 102
Fujitsu PRIMERGY BX400 S1 Options Manual preview
PRIMERGY BX400 S1
Brand: Fujitsu Pages: 60
Fujitsu PRIMERGY BX900 S1 Operating Manual preview
PRIMERGY BX900 S1
Brand: Fujitsu Pages: 144
Fujitsu Primergy BX900 S2 Operating Manual preview
Primergy BX900 S2
Brand: Fujitsu Pages: 108

Brands by name

Popular brands

Load more brands