Lenovo System x3550 M5 Installation And Service Manual Download Page 173

Page: 173 / 1144

DVD drive
connector

Cable connector latch

DVD drive cable

Figure 84. DVD drive cable routing for 3.5-inch hard disk drive server models

Step 6.

Replace the air baffle (see “Replacing the air baffle” on page 122).

Step 7.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 8.

Slide the server into the rack.

Step 9.

Reconnect the power cords and any cables that you removed.

Step 10. Turn on the peripheral devices and the server.

Removing a memory module

Use this information to remove a memory module.

To remove a dual inline memory module (DIMM), complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords.

Step 3.

Remove the cover (see “Removing the cover” on page 119).

Chapter 5

Removing and replacing components

159

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands

Lenovo System x3550 M5, Installation And Service Manual

Search results

Summary of Contents for System x3550 M5

Reviews:

Related manuals for System x3550 M5

Brands by name

Popular brands