manualshive.com logo in svg

Lenovo System x3550 M5, Installation And Service Manual

The Lenovo System x3550 M5 is a powerful and versatile server designed for exceptional performance and reliability. Its comprehensive product manual provides valuable guidance for hassle-free installation and operation. Download the user manual for free from our website, ensuring a seamless experience with your Lenovo System x3550 M5.

Share
Download
background image

d.

Press the blue release tabs and lower the battery or power module holder into the chassis.

4

Holder

Battery / flash power module

Figure 48. RAID adapter battery or flash power module installation for 3.5-inch hard disk drive server
models

Step 9.

Reinstall the cover (see “Replacing the cover” on page 120).

Step 10. Slide the server into the rack.

Step 11. Reconnect the power cords and all external cables, and turn on the server and peripheral devices.

Removing a RAID adapter battery or flash power module holder

Use this information to remove a RAID adapter battery or flash power module holder.

To remove a RAID adapter battery or flash power module holder, complete the following steps:

Note:

The following steps only apply to 2.5-inch hard disk drive server models. The RAID adapter battery or

flash power module holder cannot be removed for 3.5-inch hard disk drive server models.

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 2.

Turn off the server and peripheral devices and disconnect all power cords; then, remove the
cover (see “Removing the cover” on page 119).

Step 3.

Remove the RAID adapter battery or flash power module (see “Removing a RAID adapter battery
or flash power module” on page 123).

Chapter 5

.

Removing and replacing components

131

Summary of Contents for System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3550 M5

Qlogic iSR6200 Quick Start Manual preview
iSR6200
Brand: Qlogic Pages: 20
hager TJA670 domovea Basic Manual preview
TJA670 domovea Basic
Brand: hager Pages: 36
IBM BladeCenter JS20 Installation And User Manual preview
BladeCenter JS20
Brand: IBM Pages: 132
LaCie 301297U - 1TB Ethernet Disk XP Embedded Network Attached... Online Manual preview
301297U - 1TB Ethernet Disk XP Embedded Network Attached...
Brand: LaCie Pages: 67
Flexport HF2211 User Manual preview
HF2211
Brand: Flexport Pages: 39
Supermicro 7044H-T User Manual preview
7044H-T
Brand: Supermicro Pages: 118
Bull NovaScale T840 E2 User Manual preview
NovaScale T840 E2
Brand: Bull Pages: 210
Stratus ftServer 2500 Site Planning Manual preview
ftServer 2500
Brand: Stratus Pages: 106
Emerson Dixell XWEB300 Installation Manual preview
Dixell XWEB300
Brand: Emerson Pages: 23
Emerson DIXELL XWEB5000 PRO Installing And Operating Instructions preview
DIXELL XWEB5000 PRO
Brand: Emerson Pages: 20
Emerson CPC ISIS Installation And Configuration Manual preview
CPC ISIS
Brand: Emerson Pages: 18
Emerson Avocent ACS 6000 User Manual preview
Avocent ACS 6000
Brand: Emerson Pages: 93
Emerson Dixell XWEB300 Operation Manual preview
Dixell XWEB300
Brand: Emerson Pages: 114
Emerson Centellis 2000 Shelf Release 3.0 Manual preview
Centellis 2000 Shelf Release 3.0
Brand: Emerson Pages: 194
Emerson ATCA-7368 Installation And Use Manual preview
ATCA-7368
Brand: Emerson Pages: 222
Digi PortServer CM User Manual preview
PortServer CM
Brand: Digi Pages: 126
LG 27CN650N Owner'S Manual preview
27CN650N
Brand: LG Pages: 100
LG 24CN650N Owner'S Manual preview
24CN650N
Brand: LG Pages: 35

Brands by name

Popular brands

Load more brands