manualshive.com logo in svg

Lenovo System x3250 M5, Installation And Service Manual

The Lenovo System x3250 M5 is a powerful server designed to deliver exceptional performance and reliability. To get started with your server, you can easily access the comprehensive Product Manual that provides detailed instructions and insights. Download it for free from our website and unleash the full potential of your Lenovo System x3250 M5.

Share
Download
background image

c.

Gently push the drive into the bay until the drive stops.

d.

Rotate the tray handle to the closed (locked) position.

e.

Check the hard disk drive status LED to verify that the hard disk drive is operating correctly. If
the yellow hard disk drive status LED of a drive is lit continuously, that drive is faulty and must
be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed.

Note:

If the server is configured for RAID operation using a ServeRAID adapter, you might

have to reconfigure your disk arrays after you install hard disk drives. See the ServeRAID
adapter documentation for additional information about RAID operation and complete
instructions for using the ServeRAID adapter.

Step 4.

If you are installing additional hot-swap hard disk drives, do so now.

If you have other devices to install, do so now. Otherwise, go to “Completing the installation” on page 78.

Installing a simple-swap hard disk drive

Use this information to install a simple-swap hard disk drive.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31.

If you are installing an optional device in the server, you need to slide the server out from the rack enclosure,
turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To install a simple-swap hard disk drive, complete the following steps:

Step 1.

Remove the filler panel from the empty drive bay.

Step 2.

Touch the static-protective package that contains the drive to any unpainted metal surface on the
server; then, remove the drive from the package and place it on a static-protective surface.

Step 3.

Install the hard disk drive in the drive bay:

a.

Grasp the black drive handle and slide the blue release latch to the right and align the drive
assembly with the guide rails in the bay.

000

000

000

000

000

000000

000000

000000

000000

000000

000

000

Figure 45. 2.5-inch simple-swap hard disk drive installation

Chapter 2

.

Installing optional devices

51

Summary of Contents for System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for System x3250 M5

IBM H Series Installation And Service Manual preview
H Series
Brand: IBM Pages: 438
IBM 8832 Deployment Manual preview
8832
Brand: IBM Pages: 54
IBM 6219 - IntelliStation M - Pro Configuration And Options Manual preview
6219 - IntelliStation M - Pro
Brand: IBM Pages: 317
H3C UniServer E3200 G3 User Manual preview
UniServer E3200 G3
Brand: H3C Pages: 401
Lucent Technologies Definity 8510T User Manual preview
Definity 8510T
Brand: Lucent Technologies Pages: 85
Jung SV-SERVER-01 Operating Instructions Manual preview
SV-SERVER-01
Brand: Jung Pages: 16
TYANO GX38-B5550 Service Engineer'S Manual preview
GX38-B5550
Brand: TYANO Pages: 68
Sollae Systems CSE-H20 User Manual preview
CSE-H20
Brand: Sollae Systems Pages: 45
ACTi ACD-2000Q Quick Installation Manual preview
ACD-2000Q
Brand: ACTi Pages: 11
Asus RS160-E4 PA4 User Manual preview
RS160-E4 PA4
Brand: Asus Pages: 186
NEC 120Ra-1 Installation Manual preview
120Ra-1
Brand: NEC Pages: 12
NEC 120Rf-2 Product Manual preview
120Rf-2
Brand: NEC Pages: 20
NEC 120Le Installation Instructions Manual preview
120Le
Brand: NEC Pages: 16
NEC EXP320J User Manual preview
EXP320J
Brand: NEC Pages: 504
NEC 120Rg-2 Getting Started Manual preview
120Rg-2
Brand: NEC Pages: 2
Silex technology DS-510 Package Contents preview
DS-510
Brand: Silex technology Pages: 2
AXIOMTEK NA-100 Hardware Installation Manual preview
NA-100
Brand: AXIOMTEK Pages: 45
BITMAIN ANTMINER S19 Pro Installation Manual preview
ANTMINER S19 Pro
Brand: BITMAIN Pages: 17

Brands by name

Popular brands

Load more brands