manualshive.com logo in svg

Lenovo ideapad 305-14IBD, Hardware Maintenance Manual, Page: 45 / 89

Share
Download
Lenovo ideapad 305-14IBD Hardware Maintenance Manual Download Page 45

Lenovo ideapad 305-14IBD

41

1060 PCI Express Mini Card for wireless LAN/WAN

For access, remove these FRUs in order:

•

“1010 Battery pack” on page 34

•

“1030 Bottom slot cover” on page 37

Important:

 The preinstalled WLAN module may only be replaced with a 

Lenovo approved module in order to comply with FCC and IC regulations. Refer 
to “Table 5. Parts list—Overall” on page 71 for Lenovo part numbers for the 
approved modules.

Figure 6. Removal steps of PCI Express Mini Card for wireless LAN/WAN

Disconnect the two wireless LAN cables (black, white) 

, and then remove the 

screws .

In step 

, unplug the jacks by using the removal tool antenna RF connector

(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug 
them in the direction shown by arrows.

Notes:

 wireless LAN card has 2 cables in step 

.

Wireless LAN card in some models may have 3 cables in step 

.

Remove the card in the direction shown by arrow 

.

When installing:

 Plug the black cable into the jack labeled 

AUX

 and the white 

cable into the jack labeled 

MAIN

.

Step

Screw (quantity)

Color

Torque

M2 x 3 mm, flat-head, nylok-coated (1) 

Black

1.0~1.5kgf.cm

a

b

2

1

1

a

a

a

b

c

3

Summary of Contents for ideapad 305-14IBD


























































































Reviews:

No comments