Lenovo ideacentre 200 Hardware Maintenance Manual Download Page 106

Page: 106 / 140

7. Insert a new M.2 Wi-Fi card module into the M.2 Wi-Fi card slot. Then, pivot

the M.2 Wi-Fi card module downward.

Note:

Do not touch the notched edge of the M.2 Wi-Fi card module.

Figure 30. Installing the M.2 Wi-Fi card module

8. Install the screw to secure the M.2 Wi-Fi card module into the system board.

Then, connect the M.2 Wi-Fi antenna cables to the M.2 Wi-Fi card module.

Figure 31. Connecting the M.2 Wi-Fi antenna cables

9. Reinstall the system board frame. See “Replacing the system board frame”

on page 88.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts

replacement” on page 107.

Replacing the M.2 Wi-Fi antennas

Attention:

Do not open your computer or attempt any repair before reading and
understanding the Chapter 1 “Read this first: Important safety information” on
page 1.

ideacentre 200 Hardware Maintenance Manual

Summary of Contents for ideacentre 200












































































































































Search results

Summary of Contents for ideacentre 200

Reviews:

Lenovo ideacentre 200, Hardware Maintenance Manual, Page: 106 / 140

Search results

Summary of Contents for ideacentre 200

Reviews: