manualshive.com logo in svg

Lenovo IBM Storwize V7000, Quick Installation Manual

Share
Download
Lenovo IBM Storwize V7000 Quick Installation Manual Download Page 46

Figure 27. Expansion canister LEDs

1

Power

2

Status

3

Fault

The canister is ready with no critical errors when

Power

is illuminated,

Status

is on, and

Fault

is

off. If a canister is

not

ready, refer to the “Procedure: Understanding the system status using the

LEDs” topic in “Troubleshooting”.

Step 3.

Wait for all expansion canisters to finish powering on.

Step 4.

Power on the control enclosure. Use the supplied power cords to connect both power supply units
of the enclosure to their power sources.If the power sources have circuit breakers or switches,
ensure that they are turned on. The enclosure does not have power switches.

Note:

Each enclosure has two power supply units. To provide power failure redundancy, connect

the two power cords to separate power circuits.

Step 5.

From the rear of the control enclosure, check the LEDs on each node canister (see Figure 28
“Node canister LEDs” on page 28).

Figure 28. Node canister LEDs

1

Power

2

Status

3

Fault

The canister is ready with no critical errors when

Power

is illuminated,

Status

is flashing, and

Fault

is off. If a canister is

not

ready, refer to the “Procedure: Understanding the system status

using the LEDs” topic in “Troubleshooting”.

28

Lenovo Storage V7000 Quick Installation Guide

Summary of Contents for IBM Storwize V7000





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands