Lenovo HX1310 Installation And Service Manual Download Page 117 | Manualshive

Page: 117 / 1002

background image

• Do not leave the device where others can handle and damage it.

• While the device is still in its static-protective package, touch it to an unpainted metal surface on the

outside of the server for at least two seconds. This drains static electricity from the package and from
your body.

• Remove the device from its package and install it directly into the server without setting down the device.

If it is necessary to set down the device, put it back into its static-protective package. Do not place the
device on the server cover or on a metal surface.

• Take additional care when handling devices during cold weather. Heating reduces indoor humidity

and increases static electricity.

Updating the server configuration

When you start the server for the first time after you add or remove a device, you might receive a message
that the configuration has changed. The Setup Utility starts automatically so that you can save the new
configuration settings.

Some optional devices have device drivers that you must install. For information about installing device
drivers, see the documentation that comes with each device.

For information about configuring the integrated Gigabit Ethernet controller, see “Configuring the Ethernet
controller” on page 39.

Sending DSA data to Lenovo

You can send DSA data to Lenovo with standard upload, standard upload with the system serial number,
secure upload, and secure upload with the system serial number.

Before you send diagnostic data to Lenovo, read the terms of use at http://www.ibm.com/de/support/
ecurep/terms.html.

You can use any of the following methods to send diagnostic data to Lenovo:

•

Standard upload

:

http://www.ibm.com/de/support/ ecurep/send_http.html

•

Standard upload with the system serial number

:

http://www.ecurep.ibm.com/app/ upload_hw

•

Secure upload

:

http://www.ibm.com/de/support/ ecurep/send_http.html#secure

•

Secure upload with the system serial number

:

https://www.ecurep.ibm.com/ app/upload_hw

Returning a device or component

If you are instructed to return a device or component, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Removing and replacing server components

This section provides information for removing and replacing components in the server.

Removing and replacing components

103

«
...
115
116
117
118
119
...
»

Summary of Contents for HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX1310

Brand: IBM Pages: 84

Brand: IBM Pages: 110

Brand: IBM Pages: 214

Brand: ExtraHop Pages: 5

Brand: TYAN Pages: 170

INTUITY AUDIX LX

Brand: Avaya Pages: 68

Brand: Supermicro Pages: 124

Brand: Gigabyte Pages: 122

SuperServer E300-9C

Brand: Supermicro Pages: 113

Brand: MISUMI Pages: 18

Brand: AC&T System Pages: 32

Brand: Telvue Pages: 153

Brand: IOGear Pages: 48

PRIMERGY TX2540 M1

Brand: Fujitsu Pages: 92

PRIMERGY TX200 S5

Brand: Fujitsu Pages: 114

PRIMERGY TX300 S5

Brand: Fujitsu Pages: 142

PRIMERGY TX200 S6

Brand: Fujitsu Pages: 126

Server PRIMERGY TX1330 M1

Brand: Fujitsu Pages: 336

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands