manualshive.com logo in svg

Lenovo G555, Hardware Maintenance Manual, Page: 32 / 98

Share
Download
Lenovo G555 Hardware Maintenance Manual Download Page 32

28

Lenovo G555 Hardware Maintenance Manual

Hibernation mode

In hibernation mode, the following occurs:

The system status, RAM, VRAM, and setup data are stored on the hard disk.

•

 

The system is powered off.

•

 

To cause the computer to enter hibernation mode, follow the steps below:

If you are using the ACPI operating system and have defined one of the 

•

 

following actions as the event that causes the system to go into hibernation 

mode, perform that action: 

–  Closing the lid.
–  Pressing the power button.

Also, the computer goes into hibernation mode automatically in either of the 

following conditions:

If a “hibernation time” has been set on the timer, and if the user does not do 

•

 

any operation with the keyboard, the hard disk drive, the parallel connector, 

or the diskette drive within that time.
If the timer conditions are satisfied in suspend mode.

•

 

When the power is turned on, the computer returns from hibernation mode and 

resumes operation. The hibernation file in the boot record on the hard disk drive 

is read, and system status is restored from the hard disk drive. 

Summary of Contents for G555



































































































Reviews:

No comments