Lenovo Flex System x220 Installation And Service Manual Download Page 71 | Manualshive

Page: 71 / 714

background image

Microprocessor 2
error

Battery
error

SAS
backplane
error

Daughter
card
error

IMM
error

Microprocessor 1
error

DIMM
error 7 - 12

DIMM
error 1 - 6

Light path diagnostics LEDs

Use this information to diagnose possible errors that are indicated by the light path diagnostics LEDs.

The following table describes the LEDs on the light path diagnostics panel and the light path diagnostics
LEDs on the system board. See “Viewing the light path diagnostics LEDs” on page 61 for information
about lighting the LEDs.

Lit light path diagnostics LED

Description

None

The compute node is not sufficiently charged to display the LEDs on the system
board.

BMC error

Future use only.

Battery error

The system CMOS battery is not installed or is not working.

DC power error

Future use only.

DIMM

x

error

A memory error occurred.

I/O expansion unit

Future use only.

Light path diagnostics

The power source for the light path diagnostics LEDs is charged.

Light path diagnostics only

No errors have occurred.

Memory

A memory error has occurred.

Microprocessor

x

error

The IMM2 lights this LED when a microprocessor has failed or overheated or the
start microprocessor (CPU 1) is missing. The fault LED on the front panel is also lit.

Mismatch

The microprocessors are mismatched. If the MEM LED is also lit, the DIMMs
are mismatched.

NMI

The system board has failed.

System board

The system board has failed.

Temperature

The system temperature has exceeded a threshold level.

LSI SAS Error

A SAS error has occurred.

IMM event log

Use this information as an overview of the IMM event log.

The Integrated Management Module II (IMM2) consolidates the system-management processor functionality,
video controller, and remote presence capabilities in a single chip on the system board. The IMM2 monitors
all components of the compute node and posts events in the IMM event log. In addition, most events are
also sent to the Chassis Management Module event log. You can view the IMM event log through the
Dynamic System Analysis (DSA) program (as the ASM event log).

Troubleshooting

63

«
...
69
70
71
72
73
...
»

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x220

Link Manager 4010-43

Brand: Point Six Pages: 131

Brand: Synology Pages: 15

eServer 380 xSeries

Brand: IBM Pages: 112

IntelliStation R Pro

Brand: IBM Pages: 194

SUPERSERVER 6035B-8R+

Brand: Supero Pages: 110

SuperServer 6026TT-HIBQF

Brand: Supero Pages: 112

Brand: Dell Pages: 396

Brand: Dell Pages: 180

EqualLogic PS6010

Brand: Dell Pages: 57

PowerVault 700N

Brand: Dell Pages: 29

Brand: Dell Pages: 133

Brand: Avaya Pages: 270

NETWORK PROXY SERVER 4.0 -

Brand: Red Hat Pages: 44

NETWORK SATELLITE 5.2 - CHANNEL MANAGEMENT

Brand: Red Hat Pages: 74

Brand: Star Lake Pages: 50

Brand: Silicon Graphics Pages: 62

Brand: Silicon Graphics Pages: 70

Brand: 3onedata Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands