manualshive.com logo in svg

Lenovo Edge 2 15, Hardware Maintenance Manual

Share
Download
Lenovo Edge 2 15 Hardware Maintenance Manual Download Page 31

27

Lenovo Edge 2 15

Lenovo Edge 2 15

This chapter presents the following product-specific service references and 

product-specific parts information:
•  “Specifications” on page 27
• 

“Status indicators” on page 29

• 

“Fn key combinations” on page 30

• 

“FRU replacement notices” on page 31

• 

“Removing and replacing an FRU” on page 32

• 

“Locations” on page 55

• 

“Parts list” on page 57

Specifications

The following table lists the specifications of the Lenovo Edge 2 15:

Table 1. Specifications

Feature

Description

Form Factor

Dimensions

Appr. 380 mm x 260 mm x 19.9 mm

Weight

Appr. 2.3 kg

LCD size

15.6-inch

Processor

Processor

Click 

Start

, right-click 

File Explorer

, and 

then click 

Properties

.

Memory

Type and speed

DDR3L-1333 MHz/1600 MHz

Maximum
supported
capacity

8 GB

Slots

SODIMM × 1

Hard disk drive

Form factor

2.5-inch, 7.0 mm

Interface

SATA III

Capacity

SSHD: 500 GB+8 GB or 1 TB+8 GB
HDD: 500 GB/1 TB
SSD: 128 GB/256 GB

Summary of Contents for Edge 2 15








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands